• English
  • Русский (Russsian)

This is an old revision of the document!


Antireflective textured coatings

Elimination of undesired reflection from optical surfaces is important for many technologies. In photovoltaics reduction of reflectance from solar cells leads to enhancement of their efficiency. In telescopes and similar optical devices elimination of reflection is required to achieve better quality of image. Antireflective coatings allow to reduce the glint from a covert viewer's binoculars or telescopic sight.

To reduce reflection one can use single-layer quarter-wave coatings. The reduction of reflection is caused by destructive interference in the beams reflected from the interfaces, and constructive interference in the transmitted beams. However, as a result, single-layer coatings possess antireflective properties only for limited range of wavelengths and incidence angles.

To extend this range multi-layer coatings can be used. They are based on the same principle as single-layer coatings: destructive interference between beams reflected from different layers. Layers thickness and refractive indices should be chosen to achieve minimal reflectance in a wide wavelengths or incident angles range. The disadvantage of multi-layer coatings is difficulty to find materials with required refractive indices.


Alternative to multi-layer coatings are layers with continuously changing refractive index. Their application allows to achieve small reflectance in a wide spectral range. However, their manufacturing encounters problems with thermal mismatch, adhesion and stability of thin-film stack.

An alternative method for the reflection reduction consists in texturing the surface with 3D pyramids or 2D grooves (gratings). This method was discovered in nature by studying structure of moths' eyes. Surfaces of moths' eyes are covered with a natural nanostructured film. The film structure consists of a hexagonal pattern of bumps, each roughly 200 nm high and spaced on 300 nm centers. Since bumps are smaller than the wavelength of visible light, the light sees the surface as having a continuous refractive index gradient between the air and the medium. It leads to reflection reduction by effectively removing the air-lens interface. This allows the moth to see well in the dark, without reflections to give its location away to predators.


Moth eye.

Textured coatings have antireflective properties for wavelengths much smaller then texture size as well. In this case reflection reduction can be illustrated geometrically: rays should be reflected many times until being reverted back. At the same time transmitted rays deviate from the incident direction that leads to light trapping effect used in solar cells.

Since the seventies of the last century there is a lot of experimental studies of the properties of textured surfaces. Many reports on successful fabrication of the antireflective nanostructured surfaces appeared recently. Their use in the solar cell technology may lead to one or two orders of magnitude reduction of the surface reflection.

In the following we discuss antireflective properties of textured coatings at the whole range of their sizes including long and short wavelength limits.

Corresponding results can be also found in: http PDF

Long wavelength limit

If wavelength is much larger then texture size, optical properties of the textured coating can be described by effective medium approximation. According to this approximation, electromagnetic wave propagates in textured coating as in anisotropic medium with some effective dielectric permittivity. Below we describe how to calculate effective permittivity for following structures:

- structures which are infinite in tex:z-direction (dielectric permittivity tex:\varepsilon depends only on tex:x and tex:y).

- structures which are finite tex:z-direction.

- multi-layered structures and structures with gradually changing profile (textured coatings).


In the first case, dielectric permittivity of the structure tex:\varepsilon(x,y) is periodic in tex:xy-plane and does not depend on tex:z. One can choose tex:x and tex:y axis in such way that effective permittivity will be described by tensor tex:\hat\epsilon with 3 nonzero diagonal elements tex:\epsilon_{x}, tex:\epsilon_{y} and tex:\epsilon_z. If structure possesses central symmetry in tex:xy-plane, 2 components of this tensor should be equal tex:\epsilon_{x}=\epsilon_{y}.

Geometry optimization

In the following we consider surfaces coated by a periodic pyramid-type texture with height tex:d.


Pyramids bases have the shape of triangles, squares, hexagons and circles (in the last case pyramid is in fact a cone) with the distance between the base side and its center tex:L. The pyramids are closely packed on the substrate in the triangular or square lattice with the period tex:\Lambda.


In the following we specially distinguish two cases: complete tiling case when pyramids bases touch each other along their whole perimeter (this corresponds to the polygon base pyramids in our study) and incomplete tiling case when there are gaps between bases (this corresponds to cones). We consider normal light incidence case.


Textured surface is made from glass (the refractive index tex:n=1.5).

 
/home/kintechlab/fdtd.kintechlab.com/docs/data/attic/en/ar.1336509738.txt.gz · Last modified: 2012/05/09 00:42 by deinega     Back to top